Of course, I could just write bigger so these effects are reduced, but that's not an option. (which simply cannot be done using your proposal) and it's unacceptable to lift your stylus after having hand written a word and have AD immediately mangle it to the extent it's illegible!! When I draw something I need what I drew and not some smoothed version of it that loses vital information. I need to be able to write in cursive or doodle formulae and graphs etc. However, you are describing a usage model that doesn't serve my purpose, although I can certainly see the need for a schematic entry tool at some point down the road.Īll I'm looking for is pen and paper being replaced by stylus and tablet. Then you can open that file and do a “Save as…” under a new name and your all set to go. I, personally, would create a sheet with a border and a name and information block at the bottom right like what you might see technical draws on and save that as a “Template–Drawing” with all you defined setup information like documents units etc. You do need to spend a little time practicing with AD but in very short order you will become very proficient using it. In the end a little time spent laying out your components will be like money in the bank when you need it and you will never be sorry you took the time up front to do it. I would lay out the components first then connect them however you may need them. Unfortunately there is no way to link lines to objects or locations on objects so the lines will follow the objects. You can also use the edit fields in the “Transform” section at the bottom right to enter precise dimensions for your components. Use the “Text Art Tool” to create any text you need on your drawing.īecause of the accuracy of Affinity Designer (AD) you can zoom in really tight and create incredibly accurate components that will in the end create outstanding drawings of incredibly accurate precision. Once your components are in place simply connect them with lines using the “Pen Tool”. From the icon at the top center area you can flip any component vertically or horizontally at will with one click of the mouse This way you should only have to draw each type of component one time and can use them as many times in the future as you wish.Īlso any time you need a copy of an existing object select it then hold down the “option” key before moving it and you will get a copy. If you create a new component just copy and paste it into the Components file and save it for the future along with the others. That way the line weight will scale as you scale the object if you need that option. A trick with line widths is to make sure you have the “Scale with Object” option checked when you create a line object. As all components are vectors you can easily resize them, move them, color them, change the line widths, etc. Then open you components file and simply copy paste the components you need onto your new drawing area. Once you have these you can set up you can create a new file with the same spec’s. This will quickly become your template file. or whatever you might need in the future and save it as say, “Circuit Components”, etc. Once you have a document setup for what you need then I would use only vector drawing and create some electric component IC shapes, some resistors, diodes, pots, etc. Having done a lot of technical drawings in the past I would start by maybe setting up a document with your desired resolution (say millimeters, etc) and turn on the “Grid” from the “View” menu and turn on snap to grid under the magnet icon. Is there any way to control the over-smoothing that's going on? Is there any way to just draw as a bitmap so when I use the eraser I'm not slicing vector lines into lots of little pieces? Likewise circuit diagrams I drew also got mangled. Also, if I used the tablet to sketch handwriting or circuits etc using the paint brush (with a very small size) then when I lifted the pen after writing something the software turned the whole thing into a vector and smoothed it to the point you couldn't read a thing. However, in my first 30 seconds of usage I decided the lag with using my graphics tablet was *completely* unacceptable. I was hoping I could get all that out of AD. However, it completely blows at editing - you can't select something and change it's color, flip it in X or Y, open two documents at the same time and copy/paste between them etc. Sketchbook Pro does a fantastic job of replicating the pen/pencil and paper experience. I currently use Sketchbook Pro and my Cintiq graphics tablet as a replacement for my engineering notebook to do handwritten notes and sketch circuits, graphs and formulae. I'm not a graphics artist or designer, I'm an engineer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |